Flat 10% Off on Prepaid Orders, Apply Coupon  GET10  to get Instant 10% Discount

The FlexiForce A201/1 flex sensor is an ultra-thin and flexible printed circuit, which can be easily integrated into most applications. With its paper-thin construction, flexibility and force measurement ability, the FlexiForce force sensor can measure force between almost any two surfaces and is durable enough to stand up to most environments. FlexiForce has better force sensing properties, linearity, hysteresis, drift, and temperature sensitivity than any other thin-film force sensors.

The active sensing area is a 0.375 diameter circle at the end of the sensor. The sensor has two layers of the substrate. This substrate is composed of polyester film (or Polyimide in the case of the High-Temperature Sensors). On each layer, a conductive material (silver) is applied, followed by a layer of pressure-sensitive ink. The adhesive is then used to laminate the two layers of substrate together to form the sensor. The silver circle on top of the pressure-sensitive ink defines the active sensing area.

Silver extends from the sensing area to the connectors at the other end of the sensor, forming the conductive leads.
FlexiForce sensors are terminated with a solderable male square pin connector, which allows them to be incorporated into a circuit. The two outer pins of the connector are active and the centre pin is inactive. The length of the sensors can be trimmed to predefined lengths of 2, 4 and 6 as per the requirements. If the sensor is trimmed, a new connector must be attached. This can be accomplished by purchasing staked pin connectors and a crimping tool. A conductive epoxy can also be used to adhere to small wires to each conductor.

The sensor acts as a variable resistor in an electrical circuit. When the sensor is unloaded, its resistance is very high (greater than 5 Meg-ohm); when a force is applied to the sensor, the resistance decreases. Connecting an ohmmeter to the outer two pins of the sensor connector and applying a force to the sensing area can read the change in resistance.


Application:

An example circuit is shown below. In this case, it is driven by a -5 V DC excitation voltage. This circuit uses an inverting operational amplifier arrangement to produce an analog output based on the sensor resistance and a fixed reference resistance (RF). An analog-to-digital converter can be used to change this voltage to a digital output. In this circuit, the sensitivity of the sensor could be adjusted by changing the reference resistance (RF) and/or drive voltage (VT); a lower reference resistance and/or drive voltage will make the sensor less sensitive and increase
its active force range.

                                                                            FlexiForce A201 Sensor

Note:

The sensing area is the silver circle on the top of the sensor only.


Typical Performance:

  1. Force Range: 0-1 lb (4.4 N)
  2. Operating Temperature Range: 15F to 140F (-9C to 60C)
  3. Linearity (Error): +/- 3%
  4. Repeatability : +/- 2.5% of full scale (conditioned sensor, 80% force applied)
  5. Hysteresis: <4.5% of full scale (conditioned sensor, 80% force applied)
  6. Drift: <5% per logarithmic time scale (constant load of 90% sensor rating)
  7. Response Time: <5 microseconds
  8. Output Change/Degree F: Up to 0.2% (~0.36% / C).
    Loads <10 lbs, the operating temperature can be increased to 165F (74C).


Package Includes:

1 x FlexiForce A201/1 Flex Sensor


Specifications :-

Connector

3-pin male square pin (center pin is inactive)

Drift

< 5% per logarithmic time scale

Force Range

0-4.4N (0-0.45kg)

Hysteresis

< 4.5 % of full scale

Length ( cm )

8 Inch (20.3 cm)

Linearity (Error)

< 3% of full scale

Max Current (A)

0.2

Operating Temperature Range (C)

-9 to 60

Operating Voltage (VDC)

5

Pin Spacing (mm)

2.54

Repeatability

+/-2.5% of Full Load

Response Time ( S)

5

RoHS Compliant

Yes

Sensing Area (mm)

9.53

Surface Layer

Polyester

Thickness (mm)

0.203

Width (mm)

14


Brand/Manufacturer Generic
Country Of Origin China
Packer / Importer Address Constflick Technologies Limited, Building No 13 and 14, 3rd Floor, 2nd Main, Siddaiah Road, Bangalore, Karnataka - 560027 India.
MRP Rs. 1214.22 (Inclusive of all Taxes)
Write a review
Please login or register to review

* Product Images are shown for illustrative purposes only and may differ from actual product.

FlexiForce A201/1 Flex Sensor

  • Product Code: EC-5347
  • Availability: 2
  • Rs.2485.00
  • (Excluding 18% GST)

OR

For all Bulk & B2B Product Enquiries Kindly share your requirement at care@electronicscomp.com